Whoever first programmed that was having a seriously ‘off’ day. 620.5, 300.2, or where the decimal separator is a comma, and the delimiter is semicolon then type 620,5 300,2.īe aware that in all but the latest one or two versions of SU, using Imperial/US Customary units when the model units are metric will give you inconsistent and often WRONG conversions. ![]() Īnd if you are using measurements with a decimal point, in regions where the decimal separator is full stop (or period, in US English), and the delimiter is comma, just type it as normal - e.g. If you are using the semicolon as a separator, type instead of. Or if you wanted to keep the 300 dimension, and change the 600 to (say) 500 just type 500. Don’t click in the Measurement box first, just type. So for example if you use comma as a separator, and have set a dimension of (say) 600,300 and now want to change it to 600, 400, just type ,400 before you change to another tool. Move the cursor over onto the horizontal edge that you wish the dimension to aligned to, until you get an “On Edge” inference, and then click to complete the rotation.And if you want to keep one dimension the same, but leave the other as it is, just leave the persistent dimension out of what you typed. This is the base of the angle of rotation. Move the cursor out along the green axis until you get an “On Green Axis” inference, and click. (Release the mouse pick button when the protractor locks to the blue axis.) 2) created several pages in layout and loaded the different scenes to the viewport layer of the relevant pages 3) added dimensions on the dimension. The following is how I proceeded: 1) created Sketchup model and created the Parallel Projection scenes in Sketchup. Press and drag the cursor up along the blue (Z) axis so you get a Blue rotate around Z axis inference lock. HI Folks: I am having a problem with layout swapping scenes if the sketchup model is updated and updated in layout. Hover over the bottom vertex of the vertical edge that is being dimensioned. Ie, the closer to the origin the more powerful the axis snaps.Īlso the inference engine will also snap to other dimension’s extension lines, if both dimensions are in the same edit context, But again I experience the same reluctance to align off axis close to the origin.īTW, a dimension object like most others, can be rotated after creation. If you pull the dimension away from the edge and it snaps to one of the axis, just move it in a arc until it snaps away and the inference engine should then try the closest alignment to one of the object’s edges.ĮDIT: Actually, I do see that the axis snaps seem to be much more powerful, if the origin is one of the dimension line anchors. You need to try be patient, and let the inference engine catch up to your mouse movements. Try as I may I cannot get this dimension to snap to anything except the drawing axis. In this case the vertical dimension is off axis relative to the rear horizontal edge of the model. It’s always the simple things that are the most frustrating …………… In cases where the model axes and drawing axes are very close but not identical, is there any way to force Sketchup to align its dimensions to the model and ignore the drawing axes? So the simple question at the end of this long winded preamble is quite simply: Once again it’s clear enough in a simple drawing like this but on more complex objects with lots of dimensions this misalignment can get very scruffy and confusing. But it would be much more readable and clear if the vertical dimension aligned to the models rear horizontal edge so that its arrowhead touched the arrowhead of the width dimension. It is nonetheless accurate because the verticals in the object are on axis so the problem is less severe. However when the rotation relative to drawing axes is very small and the axes themselves are not necessarily visible in that portion of the drawing it is easy to get caught out and find you have inaccurate dimensions by reason of misalignment.Īnother problem is shown in the second screenshot. In a model this simple with the axes visible the problem is trivial and easy to see and correct. The danger being that the former produces dimensions that do not reflect true side lengths. The tool snaps to the drawing axes or the tool snaps to the model’s axes. When you use the dimension tool two possibilities occur. The top figure in the attached screen shots show a 100 x 50 x 30 mm block. I will try to explain my problem with a very over simplified example. I have developed strategies for this, but now I have reached the final dimensioning stage, I am running into difficulties. ![]() ![]() Once you leave the main drawing axes Sketchup can get quite difficult especially for referencing and snapping. So huge quantities of the drawing are ‘off axis’ rotationally. The interior I am working on is in a building where no two walls are parallel and corners are rarely right angled. I am working on a project in Sketchup 15 (16 still won’t work with El Capitan properly).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |